Dekuji byl to posledni "drobek" do skladacky (rychlost portu).
no a ze seriove linky jsem zjistil nasledujici:
Pocitam ze me ceka reinstal pomoci karty, tucne jsou zviraznene "chyby" pripadne jestli by to mohl este nekdo okomentovat bylo by to pro me super
U-Boot 2013.10-rc2-gb02fcf4 (Feb 06 2014 - 14:11:35), Build: jenkins-OpenWRT-Turris-MASTER-slaves=ubuntu-openwrt-32
CPU0: P2020E, Version: 2.1, (0x80ea0021)
Core: e500, Version: 5.1, (0x80211051)
Clock Configuration:
CPU0:1200 MHz, CPU1:1200 MHz,
CCB:600 MHz,
DDR:400 MHz (800 MT/s data rate) (Asynchronous), LBC:37.500 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
Board: TURRIS1 CPLD: V4.1 PCBA: V4.0
Error, wrong i2c adapter 2 max 2 possible
rom_loc: nor upper bank
SD/MMC : 4-bit Mode
eSPI : Enabled
I2C: Error, wrong i2c adapter 2 max 2 possible
ready
SPI: ready
DRAM: Detected UDIMM 9905428-181.A00LF
2 GiB (DDR3, 64-bit, CL=6, ECC off)
Flash: 16 MiB
L2: 512 KiB enabled
NAND: 256 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
PCIe1: Root Complex of mini PCIe SLOT, no link, regs @ 0xffe0a000
PCIe1: Bus 00 - 00
PCIe2: Root Complex of PCIe SLOT, x1, regs @ 0xffe09000
02:00.0 - 168c:0030 - Network controller
PCIe2: Bus 01 - 02
Error, wrong i2c adapter 2 max 2 possible
In: serial
Out: serial
Err: serial
Net: Phy not found
PHY reset timed out
eTSEC1, eTSEC2, eTSEC3 [PRIME]
Hit any key to stop autoboot: 0
BOOT NAND
NAND read: device 0 offset 0x0, size 0x100000
1048576 bytes read: OK
Loading from nand0, offset 0x200000
Image Name: Linux-3.10.18
Created: 2014-02-06 13:15:36 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1823906 Bytes = 1.7 MiB
Load Address: 00000000
Entry Point: 00000000
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 00200000 ...
Image Name: Linux-3.10.18
Created: 2014-02-06 13:15:36 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1823906 Bytes = 1.7 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 00400000
Booting using the fdt blob at 0x400000
Uncompressing Kernel Image ... OK
Loading Device Tree to 03ffa000, end 03fffbfc ... OK
WARNING: could not find compatible node fsl-usb2-mph or fsl-usb2-dr: FDT_ERR_NOTFOUND.
WARNING: could not find compatible node fsl-usb2-dr: FDT_ERR_NOTFOUND.
[ 0.000000] Using P2020 RDB machine description
[ 0.000000] Memory CAM mapping: 256/256 Mb, residual: 1536Mb
[ 0.000000] Linux version 3.10.18 (beast@ubuntu-openwrt) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38891) ) #1 SMP Thu Feb 6 14:15:32 CET 2014
[ 0.000000] CPU maps initialized for 1 thread per core
[ 0.000000] bootconsole [udbg0] enabled
setup_arch: bootmem
mpc85xx_rdb_setup_arch()
[ 0.000000] mpc85xx_rdb_setup_arch: Could not find Quicc Engine node
[ 0.000000] MPC85xx RDB board from Freescale Semiconductor
arch: exit
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00000000-0x1fffffff]
[ 0.000000] Normal empty
[ 0.000000] HighMem [mem 0x20000000-0x7fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x7fffffff]
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c13d8000 s6816 r8192 d13664 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 523264
[ 0.000000] Kernel command line: root=/dev/mtdblock8 rw rootfstype=jffs2 console=ttyS0,115200
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 2010296k/2097152k available (3520k kernel code, 86856k reserved, 156k data, 209k bss, 180k init)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffbf000..0xfffff000 : fixmap
[ 0.000000] * 0xffc00000..0xffe00000 : highmem PTEs
[ 0.000000] * 0xffbfd000..0xffc00000 : early ioremap
[ 0.000000] * 0xe1000000..0xffbfd000 : vmalloc & ioremap
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs
[ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff
[ 0.000000] mpic: Initializing for 256 sources
[ 0.000000] mpc85xx_rdb_pic_init: Could not find qe-ic node
[ 0.000000] clocksource: timebase mult[d555555] shift[24] registered
[ 0.006301] pid_max: default: 32768 minimum: 301
[ 0.010965] Mount-cache hash table entries: 512
[ 0.016955] mpic: requesting IPIs...
[ 0.021065] Brought up 2 CPUs
[ 0.024534] NET: Registered protocol family 16
[ 0.036094] Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->1
[ 0.043937] PCI host bridge /pcie@ffe09000 (primary) ranges:
[ 0.049583] MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
[ 0.056797] IO 0x00000000ffc10000..0x00000000ffc1ffff -> 0x0000000000000000
[ 0.063933] /pcie@ffe09000: PCICSRBAR @ 0xfff00000
[ 0.068970] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0
[ 0.076812] PCI host bridge /pcie@ffe0a000 ranges:
[ 0.081676] MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000
[ 0.088889] IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000
[ 0.096025] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
[ 0.110153] PCI: Probing PCI hardware
[ 0.113918] fsl-pci ffe09000.pcie: PCI host bridge to bus 0000:00
[ 0.119945] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.126103] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xbfffffff]
[ 0.132971] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.138483] pci 0000:00:00.0: ignoring class 0x0b2000 (doesn't match header type 01)
[ 0.154208] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.159524] fsl-pci ffe0a000.pcie: PCI host bridge to bus 0001:02
[ 0.165542] pci_bus 0001:02: root bus resource [io 0x20000-0x2ffff] (bus address [0x0000-0xffff])
[ 0.174489] pci_bus 0001:02: root bus resource [mem 0x80000000-0x9fffffff]
[ 0.181357] pci_bus 0001:02: root bus resource [bus 02-ff]
[ 0.186861] pci 0001:02:00.0: ignoring class 0x0b2000 (doesn't match header type 01)
[ 0.194729] pci 0001:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.202769] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
[ 0.208009] pci 0000:00:00.0: BAR 9: can't assign mem pref (size 0x100000)
[ 0.214808] pci 0000:01:00.0: BAR 6: assigned [mem 0xa0020000-0xa002ffff pref]
[ 0.222017] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.226972] pci 0000:00:00.0: bridge window [io 0x0000-0xffff]
[ 0.233057] pci 0000:00:00.0: bridge window [mem 0xa0000000-0xbfffffff]
[ 0.239839] pci 0001:02:00.0: PCI bridge to [bus 03]
[ 0.244793] pci 0001:02:00.0: bridge window [io 0x20000-0x2ffff]
[ 0.251052] pci 0001:02:00.0: bridge window [mem 0x80000000-0x9fffffff]
[ 0.257831] Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.265398] pci 0000:00:00.0: enabling device (0106 -> 0107)
[ 0.271049] pci 0001:02:00.0: enabling device (0106 -> 0107)
[ 0.279661] bio: create slab <bio-0> at 0
[ 0.284740] Switching to clocksource timebase
[ 0.290330] NET: Registered protocol family 2
[ 0.295034] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.302049] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.308472] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.314830] TCP: reno registered
[ 0.318000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.323836] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.330198] NET: Registered protocol family 1
[ 0.335665] bounce pool size: 64 pages
[ 0.345223] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.350980] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.361159] msgmni has been set to 983
[ 0.364895] io scheduler noop registered
[ 0.368740] io scheduler deadline registered (default)
[ 0.414079] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.422409] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550A
[ 0.429144] console [ttyS0] enabled, bootconsole disabled
[ 0.429144] console [ttyS0] enabled, bootconsole disabled
[ 0.440238] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550A
[ 0.447548] ffe04500.serial: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550
[ 0.454911] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550
[ 0.463090] ef000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101
[ 0.473114] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.478282] Amd/Fujitsu Extended Query version 1.3.
[ 0.483340] number of CFI chips: 1
[ 0.486964] 6 ofpart partitions found on MTD device ef000000.nor
[ 0.492984] Creating 6 MTD partitions on "ef000000.nor":
[ 0.498303] 0x000000000000-0x000000020000 : "NOR (RO) DTB Image"
[ 0.504826] 0x000000020000-0x0000001c0000 : "NOR (RO) Linux Kernel Image"
[ 0.512101] 0x0000001c0000-0x000000340000 : "NOR (RO) JFFS2 Root File System"
[ 0.519737] 0x000000340000-0x000000e20000 : "NOR (RO) NAND FW backup"
[ 0.526648] 0x000000e40000-0x000000f00000 : "NOR (RW) Cert backup"
[ 0.533332] 0x000000f00000-0x000001000000 : "NOR (RO) U-Boot Image"
[ 0.545030] ONFI param page 0 valid
[ 0.548566] ONFI flash detected
[ 0.551748] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64
[ 0.563547] Bad block table found at page 131008, version 0x01
[ 0.570093] Bad block table found at page 130944, version 0x01
[ 0.576565] 3 ofpart partitions found on MTD device ff800000.flash
[ 0.582753] Creating 3 MTD partitions on "ff800000.flash":
[ 0.588243] 0x000000000000-0x000000200000 : "NAND (RW) DTB Image"
[ 0.594892] 0x000000200000-0x000000700000 : "NAND (RW) Linux Kernel Image"
[ 0.602270] 0x000000700000-0x000010000000 : "NAND (RW) JFFS2 Root File System"
[ 0.610084] eLBC NAND device at 0xff800000, bank 1
[ 0.615306] fsl_espi ffe07000.spi: master is unqueued, this is deprecated
[ 0.622107] fsl_espi ffe07000.spi: at 0xe103c000 (irq = 59)
[ 0.628101] ar8216: Module init.
[ 0.631798] libphy: Fixed MDIO Bus: probed
[ 0.636147] libphy: Freescale PowerQUICC MII Bus: probed
[ 0.641802] ar8216: probe addr 0.
[ 0.645249] phy_id: 4dd036, ar8xxx_phy_ids: 4dd033
[ 0.650302] phy_id: 4dd036, ar8xxx_phy_ids: 4dd034
[ 0.655353] phy_id: 4dd036, ar8xxx_phy_ids: 4dd036
[ 0.660508] phy_id: 4dd036, ar8xxx_phy_ids: 4dd033
[ 0.665560] phy_id: 4dd036, ar8xxx_phy_ids: 4dd034
[ 0.670612] phy_id: 4dd036, ar8xxx_phy_ids: 4dd036
[ 0.675766] phy_id: 4dd036, ar8xxx_phy_ids: 4dd033
[ 0.680818] phy_id: 4dd036, ar8xxx_phy_ids: 4dd034
[ 0.685870] phy_id: 4dd036, ar8xxx_phy_ids: 4dd036
[ 0.691024] phy_id: 4dd036, ar8xxx_phy_ids: 4dd033
[ 0.696076] phy_id: 4dd036, ar8xxx_phy_ids: 4dd034
[ 0.701128] phy_id: 4dd036, ar8xxx_phy_ids: 4dd036
[ 0.706179] ar8216: gonna list.
[ 0.709317] ar8216: after list.
[ 0.712455] ar8216: Identifying chip.
[ 0.739310] switch0: Atheros AR8327 rev. 2 switch registered on mdio@ffe24520
[ 0.746454] ar8216: FOUND!!!.
[ 1.962154] fsl-gianfar ffe24000.ethernet eth0: mac: 00:00:00:00:00:00
[ 1.968693] fsl-gianfar ffe24000.ethernet eth0: Running with NAPI enabled
[ 1.975488] fsl-gianfar ffe24000.ethernet eth0: RX BD ring size for Q[0]: 256
[ 1.982628] fsl-gianfar ffe24000.ethernet eth0: TX BD ring size for Q[0]: 256
[ 1.990213] fsl-gianfar ffe25000.ethernet eth1: mac: 00:00:00:00:00:00
[ 1.996753] fsl-gianfar ffe25000.ethernet eth1: Running with NAPI enabled
[ 2.003551] fsl-gianfar ffe25000.ethernet eth1: RX BD ring size for Q[0]: 256
[ 2.010693] fsl-gianfar ffe25000.ethernet eth1: TX BD ring size for Q[0]: 256
[ 2.018271] fsl-gianfar ffe26000.ethernet eth2: mac: 00:00:00:00:00:00
[ 2.024813] fsl-gianfar ffe26000.ethernet eth2: Running with NAPI enabled
[ 2.031645] fsl-gianfar ffe26000.ethernet eth2: RX BD ring size for Q[0]: 256
[ 2.038787] fsl-gianfar ffe26000.ethernet eth2: TX BD ring size for Q[0]: 256
[ 2.046043] ucc_geth_driver: QE UCC Gigabit Ethernet Controller
[ 2.052344] i2c /dev entries driver
[ 2.056009] mpc-i2c ffe03000.i2c: timeout 1000000 us
[ 2.063632] rtc-mcp7940 0-006f: rtc core: registered mcp7940 as rtc0
[ 2.070065] mpc-i2c ffe03100.i2c: timeout 1000000 us
[ 2.075370] booke_wdt: powerpc book-e watchdog driver loaded
[ 2.081402] TCP: cubic registered
[ 2.084714] NET: Registered protocol family 17
[ 2.089238] Bridge firewalling registered
[ 2.093256] 8021q: 802.1Q VLAN Support v1.8
[ 2.098894] rtc-mcp7940 0-006f: setting system clock to 2014-09-12 12:01:11 UTC (1410523271)
[ 3.910967] jffs2: notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 3.929922] VFS: Mounted root (jffs2 filesystem) on device 31:8.
[ 3.936128] Freeing unused kernel memory: 180K (c0343000 - c0370000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
ifconfig: SIOCSIFFLAGS: Cannot assign requested address
sendto(): Network is unreachable
Press the [f] key and hit [enter] to enter failsafe mode
[ 5.456339] usbcore: registered new interface driver usbfs
[ 5.461933] usbcore: registered new interface driver hub
[ 5.467381] usbcore: registered new device driver usb
[ 5.474694] Button Hotplug driver version 0.4.1
[ 5.489089] SCSI subsystem initialized
[ 5.495449] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.502048] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 5.508681] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 5.515974] fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000
[ 5.533068] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 5.538982] hub 1-0:1.0: USB hub found
[ 5.542759] hub 1-0:1.0: 1 port detected
[ 5.547262] ehci-platform: EHCI generic platform driver
[ 5.557636] sdhci: Secure Digital Host Controller Interface driver
[ 5.563836] sdhci: Copyright(c) Pierre Ossman
[ 5.568587] sdhci-pltfm: SDHCI platform and OF driver helper
[ 5.605046] mmc0: SDHCI controller on ffe2e000.sdhc [ffe2e000.sdhc] using DMA
[ 5.616026] usbcore: registered new interface driver usb-storage
[ 5.857053] usb 1-1: new high-speed USB device number 2 using fsl-ehci
[ 5.993837] hub 1-1:1.0: USB hub found
[ 5.997727] hub 1-1:1.0: 2 ports detected
mount_root: mounting /dev/root
ifconfig: SIOCSIFFLAGS: Cannot assign requested address
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 8.752560] NET: Registered protocol family 10
[ 8.763784] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 8.772820] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 8.787644] Loading modules backported from Linux version master-2013-11-05-0-gafa3093
[ 8.795600] Backport generated by backports.git backports-20130802-0-gdb67a3f
[ 8.807281] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.866815] usbcore: registered new interface driver ums-alauda
[ 8.873303] usbcore: registered new interface driver ums-cypress
[ 8.880053] usbcore: registered new interface driver ums-datafab
[ 8.886812] usbcore: registered new interface driver ums-freecom
[ 8.893689] usbcore: registered new interface driver ums-isd200
[ 8.900413] usbcore: registered new interface driver ums-jumpshot
[ 8.907280] usbcore: registered new interface driver ums-karma
[ 8.914130] usbcore: registered new interface driver ums-sddr09
[ 8.920942] usbcore: registered new interface driver ums-sddr55
[ 8.927752] usbcore: registered new interface driver ums-usbat
[ 8.938227] xt_time: kernel timezone is -0000
[ 8.950965] cfg80211: Calling CRDA to update world regulatory domain
[ 8.957628] cfg80211: World regulatory domain updated:
[ 8.962795] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.970989] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.978748] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.986504] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.994257] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 9.002015] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 9.009773] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 9.063924] PPP generic driver version 2.4.2
[ 9.068996] NET: Registered protocol family 24
[ 9.237712] cfg80211: Calling CRDA for country: US
[ 9.242858] cfg80211: Regulatory domain changed to country: US
[ 9.248730] cfg80211: DFS Master region FCC
[ 9.252836] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.261198] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 9.268996] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 1700 mBm)
[ 9.276753] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
[ 9.284506] cfg80211: (5490000 KHz - 5600000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
[ 9.292259] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2400 mBm)
[ 9.300012] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 3000 mBm)
[ 9.307763] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 9.315623] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xf3540000, irq=24
[ 18.326045] ar8216: Module config init.
[ 18.330255] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.337929] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 18.345675] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 18.885633] ar8216: Module config init.
[ 18.889778] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.895953] device eth0 entered promiscuous mode
[ 18.902512] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 18.911449] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 18.917481] device eth1 entered promiscuous mode
[ 19.057500] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 19.889045] ar8216: config aneg.
[ 20.895482] libphy: mdio@ffe24520:00 - Link is Up - 1000/Full
[ 20.901332] br-lan: port 1(eth0) entered forwarding state
[ 20.906762] br-lan: port 1(eth0) entered forwarding state
[ 20.912200] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 20.919539] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 20.926951] libphy: fixed-0:06 - Link is Up - 1000/Full
[ 20.932685] br-lan: port 2(eth1) entered forwarding state
[ 20.938115] br-lan: port 2(eth1) entered forwarding state
[ 20.943621] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 22.909040] br-lan: port 1(eth0) entered forwarding state
[ 22.941041] br-lan: port 2(eth1) entered forwarding state
procd: - init complete -
procd: Instance log::instance1 s in a crash loop 6 crashes, 0 seconds since last crash
bohuzel sem to musel rozdelit do dvou postu
V routeru je vestavěn převodník USB2serial, myslím, že od FTDI. Seženete-li příslušný ovladač, začne se turris tvářit jako nový sériový port (např. COM3), na který se z PuTTY připojíte.
Dobrý den, pod win7 jsem neměl s připojením na sériovou linku žádný problém. Po zapojení se objevilo další zařízení (v mém případě COM34) a v Putty jsem se na něj připojil (rychlost je třeba nastavit na 115200).
Fórum
